Finished Rosewood Concrete driveway with a curved approach and clean control joints

    Rosewood Concrete · Tualatin, Oregon

    Concrete Driveways Tualatin, OR

    Concrete driveways built for Tualatin’s wet winters and slow-draining soil. We handle replacements, new pours, widening, and the city permits that come with them.

    Licensed, bonded, and insured · CCB #263019

    Most driveway damage in Tualatin starts where you can’t see it. From fall through spring, rain soaks the ground under the slab. The soil goes soft, and a slab sitting on a thin base starts to sink, tilt, and crack. So we start underneath. Rosewood Concrete digs to firm subgrade, builds a compacted rock base, and sets the grade so water runs off the slab and away from your house.

    Here’s how it starts. We come out, measure, and look at the slope, the soil, and how a truck gets in. Then you get a written quote that spells out thickness, mix, rebar, joint layout, and permits. Most quotes go out within 48 hours of the visit.

    Licensed, bonded, and insured · Oregon CCB #263019 · Fixed-price written quotes

    Driveway Concrete Work We Do in Tualatin

    Driveway Replacement

    First, the old slab has to come out clean. We saw cut it, break it up, and haul it to a Metro-authorized transfer station or a concrete recycler. Then we dig to firm ground and rebuild the base before any new concrete shows up. Skip that step, and the new slab cracks the same way the old one did.

    New Driveways

    Building a new home or ADU, or finally paving that gravel strip? We grade the area so water heads to the street or a drain. Then we form the slab to the width and turning room you’ll actually use every day.

    Widening and Parking Pads

    Got a second car, a work van, or a boat that needs a spot? We widen the driveway or add a side pad. The seam between old and new concrete gets planned as a joint, so each section can move without cracking its neighbor. Need a wider curb cut too? The city reviews that first, and we take care of the paperwork.

    Driveway Approaches

    The approach is the piece between the street and your property line, where the driveway crosses the sidewalk. In Tualatin, that strip sits in the public right of way, so City Engineering has a say. We pull the permit, build to city standards, and book the inspections.

    RV Pads and Heavy Use Slabs

    An RV, a loaded trailer, or a delivery truck weighs a lot more than your car. These slabs get 5 to 6 inches of concrete with #4 rebar on 18-inch centers, so they stay flat under the load.

    Decorative Finishes

    Want something beyond plain gray? Exposed aggregate, integral color, and stamped or paver borders give a driveway a finished look that suits the house.

    Completed concrete driveway with a broom finish and carefully placed joints

    Why Tualatin Driveways Crack, and How We Prevent It

    Tualatin gets about 44 inches of rain a year, and December is the wettest month at around 7 inches. Most of the city sits on the Tualatin Valley floor, on silty soil the Missoula Floods left behind at the end of the last ice age. That silt drains slowly. When it stays wet all winter, it can’t hold a slab level.

    Let’s break it down. Most failed driveways here trace back to one of three things:

    1. Water under the slab. A thin or loose base traps water against the soil, and the slab settles unevenly. Our fix: dig to firm subgrade, then lay 4 to 6 inches of 3/4-inch minus crushed rock, compacted in 2-inch lifts. Water drains out sideways instead of sitting under the concrete.
    2. Surface scaling. Tualatin sees about 3 inches of snow in an average year, plus plenty of freezing nights. Water in the surface freezes, expands, and pops the top layer loose. That’s why every driveway and apron we pour uses air-entrained 4,000 psi concrete. Its tiny air pockets give freezing water room to expand.
    3. Joints in the wrong place. Concrete shrinks as it cures, and it’s going to crack somewhere. On a 4-inch slab, we saw cut control joints every 8 to 12 feet on pour day, so cracks follow straight lines we chose. Expansion material separates the driveway from the garage slab, the house, and the sidewalk.

    One more thing. Every driveway gets at least 1/8 inch per foot of fall away from the house, so rain runs off the slab and not toward your foundation.

    Compacted crushed-rock base and wooden forms before a driveway pour

    Tualatin Driveway Permits

    Tualatin splits driveway work across a few permits, and the ones you need depend on what’s changing. We sort that out at the site visit, so nothing surprises you halfway through the job.

    Rebuilding an Existing Approach or Sidewalk

    Rebuilding or changing an existing approach or sidewalk in the right of way takes a Driveway Approach & Sidewalk Permit from City of Tualatin Engineering. Your contractor needs an Oregon CCB license and proof of insurance. The city also asks for financial assurance worth twice the construction cost. So a $4,000 approach means an $8,000 bond, cash deposit, or check. Fees follow the city’s fee schedule.

    New, Moved, or Wider Approaches

    A brand-new approach, a moved one, or a wider one can trigger a driveway approach permit under Tualatin Development Code Chapter 75. It’s a Type II land use review. City staff decide, neighbors get notice, and the decision can be appealed to City Council. You’ll need a site plan plus service provider letters from Clean Water Services and Tualatin Valley Fire & Rescue, so plan on more time than a simple repair. If your project needs this review, we build that time into the schedule up front.

    Street Trees

    Here’s one that catches people off guard. In Tualatin, homeowners are responsible for the street trees out front. Taking one out for a wider driveway requires a Street Tree permit, and each tree you remove gets replaced with a species from the city’s approved list.

    Added Hard Surface

    More hard surface, like a wider driveway or a new parking pad, can bring a stormwater development charge set with Clean Water Services. We check this before we quote, so it’s already in your number.

    State Highways

    Does your driveway connect to a state highway? Then it goes through an ODOT access permit instead of the city’s driveway approach permit.

    Once the work wraps up, you get the closed permit and inspection records for your files.

    Finishes for Tualatin Driveways

    For most Tualatin driveways, we recommend a broom finish. The texture gives tires and shoes grip on wet mornings and in the mossy shade under mature trees.

    • Broom finish: Best traction and lowest cost. It’s our standard.
    • Exposed aggregate: Washed to show the stone underneath. It hides tire marks and wears well.
    • Integral color: Mixed into the concrete before it’s placed, so the color goes all the way through and won’t wear off.
    • Stamped or paver borders: A decorative edge around a broom-finished field, without the upkeep of a full paver driveway.

    Smooth steel-trowel finishes? We save those for garage floors, which stay dry. Outside, smooth concrete gets slick fast in the rain.

    Timeline and What Affects the Price

    A typical driveway replacement takes 3 to 5 working days on site, from tear out to final finish. Permits come first, and a Type II approach review adds the most time.

    After the pour, here’s what to expect:

    • Foot traffic: 24 to 48 hours
    • Cars and trucks: 10 to 14 days
    • Sealing: around 28 days, on finishes that call for it

    We pour all year and plan around the forecast. Summer moves fastest. In winter, fresh concrete gets insulated blankets, a cold-weather mix, and cover from heavy rain while it sets.

    We price every Tualatin driveway after a free site visit. Here’s why: each of these moves the number.

    • Size and thickness: A 6-inch RV pad takes 50% more concrete than a 4-inch car slab.
    • Tear out and disposal: Old concrete is heavy, and hauling is priced by volume.
    • Base work: Soft, wet ground means digging deeper and bringing in more rock.
    • Access: A tight side yard or a long run from the street may mean pumping the concrete.
    • Finish: Broom costs the least. Exposed aggregate, color, and stamping add to it.
    • Permits and bonds: These add the most when a new or wider approach needs a Type II review.

    Your quote comes as a fixed price in writing, with the mix, thickness, rebar, joint plan, and dates all listed.

    The same driveway after the concrete pour and finishing
    Prepared driveway base and forms before concrete placement
    BeforeAfter

    Where We Pour in Tualatin

    We pour driveways in every corner of Tualatin, across all six residential CIO areas: Byrom, East, Ibach, Martinazzi Woods, Midwest, and Riverpark. That covers homes along the Tualatin River, the streets around Tualatin Commons, and the newer subdivisions at the edges of town.

    We also serve nearby Tigard, Durham, King City, Wilsonville, West Linn, Sherwood, Lake Oswego, and Beaverton.

    Need a patio, walkway, retaining wall, or foundation? Head to our page for concrete contractors in Tualatin.

    Why Tualatin Homeowners Choose Rosewood Concrete

    • Licensed, bonded, and insured: Oregon CCB #263019, which you can check on the CCB license search.
    • One point of contact: The person who measures your driveway sees it through to the final walkthrough.
    • Permits handled: Engineering permits, Type II reviews, street tree permits, and 811 utility locates. We file them so you don’t have to.
    • Written scope: Thickness, mix, rebar, and joint layout, all in writing before we start.
    • Clean job site: We haul the old concrete away and clean up before we leave.
    FAQ

    Driveway Concrete FAQs for Tualatin, OR

    Get a Driveway Concrete Quote in Tualatin

    Ready to get started? Send us your address, rough measurements, and a photo of your current driveway. We’ll come measure, check the soil and drainage, sort out the permits, and send a fixed-price proposal with the full spec on it.

    Call (971) 289-6488

    Get Your Free Quote

    Step 1 of 5: Contact Info